 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. *This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specificaions approval sheet for product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the before ordering. C02E10.pdf 04.1.20 Chip Monolithic Ceramic Capacitors Medium-voltage High-Capacitance for General-Use e g e s Features 1. A new monolithic structure for small, high capacitance capable of operating at high voltage levels. 2. Sn-plated external electrodes realized good solderability. 3. Use the GRM18/21/31 types with flow or reflow www..com and other types with reflow soldering soldering, only. L W T Part Number s Applications 1. Ideal for use as a hot-cold coupling for DC/DC converter. 2. Ideal for use on line filters and ringer detectors for telephones, facsimiles and modems. 3. Ideal for use on diode-snubber circuits for switching power supplies. Rated Voltage (V) DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC250 DC630 DC630 DC630 TC Code (Standard) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) GRM188 0.8 0.1 1.6 0.1 0.8 0.1 0.2 to 0.5 GRM21A 2.0 0.2 1.25 0.2 1.0 +0,-0.3 1.25 0.2 GRM21B GRM31B 3.2 0.2 1.6 0.2 1.25 +0,-0.3 GRM31C 1.6 0.2 GRM32Q 3.2 0.3 2.5 0.2 1.5 +0,-0.3 0.3 min. GRM32D 2.0 +0,-0.3 GRM43Q 1.5 +0,-0.3 4.5 0.4 3.2 0.3 GRM43D 2.0 +0,-0.3 5.7 0.4 5.0 0.4 2.0 +0,-0.3 GRM55D * GRM55DR73A : 2.5mm min. L Dimensions (mm) W T e g min. 0.4 0.7 1.2 2.2 3.2* Part Number GRM188R72E221KW07D GRM188R72E331KW07D GRM188R72E471KW07D GRM188R72E681KW07D GRM188R72E102KW07D GRM21AR72E102KW01D GRM188R72E152KW07D GRM21AR72E152KW01D GRM188R72E222KW07D GRM21AR72E222KW01D GRM21AR72E332KW01D GRM21AR72E472KW01D GRM21AR72E682KW01D GRM21BR72E103KW03L GRM31BR72E153KW01L GRM31BR72E223KW01L GRM31CR72E333KW03L GRM31CR72E473KW03L GRM32QR72E683KW01L GRM31CR72E104KW03L GRM32DR72E104KW01L GRM43QR72E154KW01L GRM32DR72E224KW01L GRM43DR72E224KW01L GRM43DR72E334KW01L GRM55DR72E334KW01L GRM43DR72E474KW01L GRM55DR72E474KW01L GRM55DR72E105KW01L GRM31BR72J102KW01L GRM31BR72J152KW01L GRM31BR72J222KW01L Capacitance 220pF 10% 330pF 10% 470pF 10% 680pF 10% 1000pF 10% 1000pF 10% 1500pF 10% 1500pF 10% 2200pF 10% 2200pF 10% 3300pF 10% 4700pF 10% 6800pF 10% 10000pF 10% 15000pF 10% 22000pF 10% 33000pF 10% 47000pF 10% 68000pF 10% 0.10F 10% 0.10F 10% 0.15F 10% 0.22F 10% 0.22F 10% 0.33F 10% 0.33F 10% 0.47F 10% 0.47F 10% 1.0F 10% 1000pF 10% 1500pF 10% 2200pF 10% Length L Width W Thickness T (mm) (mm) (mm) 1.6 1.6 1.6 1.6 1.6 2.0 1.6 2.0 1.6 2.0 2.0 2.0 2.0 2.0 3.2 3.2 3.2 3.2 3.2 3.2 3.2 4.5 3.2 4.5 4.5 5.7 4.5 5.7 5.7 3.2 3.2 3.2 0.8 0.8 0.8 0.8 0.8 1.25 0.8 1.25 0.8 1.25 1.25 1.25 1.25 1.25 1.6 1.6 1.6 1.6 2.5 1.6 2.5 3.2 2.5 3.2 3.2 5.0 3.2 5.0 5.0 1.6 1.6 1.6 0.8 0.8 0.8 0.8 0.8 1.0 0.8 1.0 0.8 1.0 1.0 1.0 1.0 1.25 1.25 1.25 1.6 1.6 1.5 1.6 2.0 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 1.25 1.25 1.25 Electrode g min. (mm) 0.4 0.4 0.4 0.4 0.4 0.7 0.4 0.7 0.4 0.7 0.7 0.7 0.7 0.7 1.2 1.2 1.2 1.2 1.2 1.2 1.2 2.2 1.2 2.2 2.2 3.2 2.2 3.2 3.2 1.2 1.2 1.2 Electrode e (mm) 0.2 to 0.5 0.2 to 0.5 0.2 to 0.5 0.2 to 0.5 0.2 to 0.5 0.3 min. 0.2 to 0.5 0.3 min. 0.2 to 0.5 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 15 Continued on the following page. 109 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. *This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specificaions approval sheet for product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the before ordering. C02E10.pdf 04.1.20 Continued from the preceding page. Part Number GRM31BR72J332KW01L GRM31BR72J472KW01L GRM31BR72J682KW01L GRM31BR72J103KW01L GRM31CR72J153KW03L GRM32QR72J223KW01L GRM32DR72J333KW01L GRM32DR72J473KW01L GRM43QR72J683KW01L GRM43DR72J104KW01L GRM55DR72J154KW01L GRM55DR72J224KW01L GRM31BR73A102KW01L www..com GRM31BR73A152KW01L GRM31BR73A222KW01L GRM31BR73A332KW01L GRM31BR73A472KW01L GRM32QR73A682KW01L GRM32QR73A103KW01L GRM32DR73A153KW01L GRM32DR73A223KW01L GRM43DR73A333KW01L GRM43DR73A473KW01L GRM55DR73A104KW01L Rated Voltage (V) DC630 DC630 DC630 DC630 DC630 DC630 DC630 DC630 DC630 DC630 DC630 DC630 DC1000 DC1000 DC1000 DC1000 DC1000 DC1000 DC1000 DC1000 DC1000 DC1000 DC1000 DC1000 TC Code (Standard) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) X7R (EIA) Capacitance 3300pF 10% 4700pF 10% 6800pF 10% 10000pF 10% 15000pF 10% 22000pF 10% 33000pF 10% 47000pF 10% 68000pF 10% 0.10F 10% 0.15F 10% 0.22F 10% 1000pF 10% 1500pF 10% 2200pF 10% 3300pF 10% 4700pF 10% 6800pF 10% 10000pF 10% 15000pF 10% 22000pF 10% 33000pF 10% 47000pF 10% 0.10F 10% Length L Width W Thickness T (mm) (mm) (mm) 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 4.5 4.5 5.7 5.7 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 4.5 4.5 5.7 1.6 1.6 1.6 1.6 1.6 2.5 2.5 2.5 3.2 3.2 5.0 5.0 1.6 1.6 1.6 1.6 1.6 2.5 2.5 2.5 2.5 3.2 3.2 5.0 1.25 1.25 1.25 1.25 1.6 1.5 2.0 2.0 1.5 2.0 2.0 2.0 1.25 1.25 1.25 1.25 1.25 1.5 1.5 2.0 2.0 2.0 2.0 2.0 Electrode g min. (mm) 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 2.2 2.2 3.2 3.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 2.2 2.2 2.5 Electrode e (mm) 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 0.3 min. 15 110 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. *This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specificaions approval sheet for product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the before ordering. C02E10.pdf 04.1.20 Specifications and Test Methods No. 1 2 3 Item Operating Temperature Range Appearance Dimensions Y55 to W125D No defects or abnormalities Within the specified dimensions Visual inspection Using calipers No failure should be observed when 150% of the rated voltage (200% of the rated voltage in case of rated voltage : DC250V, 120% of the rated voltage in case of rated voltage : DC1kV) is applied between the terminations for 1 to 5 sec., provided the charge/discharge current is less than 50mA. The insulation resistance should be measured with DC500T50V (DC250T50V in case of rated voltage : DC250V) and within 60T5 sec. of charging. The capacitance/D.F. should be measured at 25D at a frequency of 1T0.2kHz and a voltage of AC1T0.2V (r.m.s.) #Pretreatment Perform a heat treatment at 150 W0 D for 60T5 min. and then Y10 let sit for 24T2 hrs. at *room condition. The range of capacitance change compared with the 25D value within Y55 to W125D should be within the specified range. #Pretreatment Perform a heat treatment at 150 W0 D for 60T5 min. and then Y10 let sit for 24T2 hrs. at *room condition. Solder the capacitor to the testing jig (glass epoxy board) shown in Fig. 1 using a eutectic solder. Then apply 10N force in the direction of the arrow. The soldering should be done either with an iron or using the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. 10N (5N : Size 1.6g0.8mm only), 10T1s Speed : 1.0mm/s Glass Epoxy Board Specifications Test Method Y 4 Dielectric Strength No defects or abnormalities 5 Insulation Resistance (I.R.) Capacitance Dissipation Factor (D.F.) Capacitance Temperature Characteristics CU0.01F : More than 100M * F CF0.01F : More than 10,000M Within the specified tolerance www..com 6 7 0.025 max. 8 Cap. Change Within T15% (Temp. Range : Y55 to W125D) 9 Adhesive Strength of Termination No removal of the terminations or other defect should occur. Fig. 1 Appearance Capacitance No defects or abnormalities Within the specified tolerance Solder the capacitor to the test jig (glass epoxy board). The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 55Hz. The frequency range, from 10 to 55Hz and return to 10Hz, should be traversed in approximately 1 min. This motion should be applied for a period of 2 hrs. in each 3 mutually perpendicular directions (total of 6 hrs.). 10 Vibration Resistance D.F. 0.025 max. 15 Solder resist Cu Glass Epoxy Board No cracking or marking defects should occur. TR S QT S Q , R , T S d c 40 a 100 t : 1.6 b 4.5 Solder the capacitor to the testing jig (glass epoxy board) shown in Fig. 2 using a eutectic solder. Then apply a force in the direction shown in Fig. 3. The soldering should be done either with an iron or using the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. 20 50 Pressurizing speed : 1.0mm/s Pressurize R230 Flexure=1 Capacitance meter 45 45 11 Deflection LZW (mm) 1.6Z0.80 2.0Z1.25 3.2Z1.60 3.2Z2.50 4.5Z3.20 5.7Z5.00 a 1.0 1.2 2.2 2.2 3.5 4.5 Dimension (mm) b c 1.25 3.0 1.65 4.0 2.05 5.0 2.95 5.0 3.75 7.0 5.65 8.0 d (in mm) 1.0 Fig. 3 Fig. 2 * "Room condition" Temperature : 15 to 35D, Relative humidity : 45 to 75%, Atmospheric pressure : 86 to 106kPa Continued on the following page. 111 Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc. *This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specificaions approval sheet for product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the before ordering. C02E10.pdf 04.1.20 Specifications and Test Methods Continued from the preceding page. No. Item Specifications Test Method Immerse the capacitor in a solution of ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight proportion). Immerse in eutectic solder solution for 2T0.5 sec. at 235T5D. Immersing speed : 25T2.5mm/s Preheat the capacitor at 120 to 150D* for 1 min. Immerse the capacitor in eutectic solder solution at 260T5D for 10T1 sec. Let sit at *room condition for 24T2 hrs., then measure. #Immersing speed : 25T2.5mm/s #Pretreatment Perform a heat treatment at 150 W00 D for 60T5 min. and then Y10 let sit for 24T2 hrs. at *room condition. *Preheating for more than 3.2Z2.5mm 12 Solderability of Termination Appearance Capacitance Change D.F. 75% of the terminations are to be soldered evenly and continuously. No marking defects Within T10% 0.025 max. CU0.01F : More than 100M * F CF0.01F : More than 10,000M Resistance 13 to Soldering Heat I.R. www..com Dielectric Strength In accordance with item No.4 Step 1 2 Temperature 100D to 120D 170D to 200D Time 1 min. 1 min. Appearance Capacitance Change D.F. I.R. No marking defects Within T7.5% 0.025 max. CU0.01F : More than 100M * F CF0.01F : More than 10,000M 14 Temperature Cycle Fix the capacitor to the supporting jig (glass epoxy board) shown in Fig. 4 using a eutectic solder. Perform the 5 cycles according to the 4 heat treatments listed in the following table. Let sit for 24T2 hrs. at *room condition, then measure. Time (min.) Temperature (D) Step 30T3 Min. Operating Temp.T3 1 2 to 3 Room Temp. 2 30T3 Max. Operating Temp.T2 3 2 to 3 Room Temp. 4 #Pretreatment Perform a heat treatment at 150 W00 D for 60T5 min. and then Y10 let sit for 24T2 hrs. at *room condition. Dielectric Strength In accordance with item No.4 Solder resist Cu Glass Epoxy Board Fig. 4 Appearance Capacitance Change 15 Humidity (Steady State) D.F. I.R. Dielectric Strength Appearance Capacitance Change 16 Life D.F. I.R. Dielectric Strength Appearance Humidity Loading (Application : DC250V, DC630V item) Capacitance Change D.F. I.R. Dielectric Strength No marking defects Within T15% 0.05 max. CU0.01F : More than 10M * F CF0.01F : More than 1,000M In accordance with item No.4 No marking defects Within T15% (rated voltage : DC250V, DC630V) Within T20% (rated voltage : DC1kV) 0.05 max. CU0.01F : More than 10M * F CF0.01F : More than 1,000M In accordance with item No.4 No marking defects Within T15% 0.05 max. CU0.01F : More than 10M * F CF0.01F : More than 1,000M In accordance with item No.4 Apply the rated voltage at 40T2D and relative humidity of 90 to 95% for 500 W24 hrs. Y00 Remove and let sit for 24T2 hrs. at *room condition, then measure. #Pretreatment Apply test voltage for 60T5 min. at test temperature. Remove and let sit for 24T2 hrs. at *room condition. Apply 120% of the rated voltage (150% of the rated voltage in case of rated voltage : DC250V, 110% of the rated voltage in case of rated voltage : DC1kV) for 1,000 W48 hrs. at maximum Y00 operating temperature T3D. Remove and let sit for 24 T2 hrs. at *room condition, then measure. The charge/discharge current is less than 50mA. #Pretreatment Apply test voltage for 60T5 min. at test temperature. Remove and let sit for 24T2 hrs. at *room condition. Let the capacitor sit at 40T2D and relative humidity of 90 to 95% for 500 W24 hrs. Y00 Remove and let sit for 24T2 hrs. at *room condition, then measure. #Pretreatment Perform a heat treatment at 150 W00 D for 60T5 min. and then Y10 let sit for 24T2 hrs. at *room condition. 15 17 * "Room condition" Temperature : 15 to 35D, Relative humidity : 45 to 75%, Atmospheric pressure : 86 to 106kPa 112 |
Price & Availability of GRM21AXXXXXX
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |